There’s a Kickstarter up called Linked to the Wall, which aims to create game cartridge wall mounts. The driving idea they have is that games are made into similar form as paintings, framed to the wall. The idea seems to be solid in principle, but there’s few problems, one logistic, that they are either side-stepping or haven’t thought about.
Looking at the prototypes they have, I have to question why do they need to create separate wall mounts to different cartridges. They want to streamline and eliminate all possible manufacturing problems by creating a solid piece of plastic, which is understandable and admirable to a point, but also tells me they want to produce these as cheaply and fast as possible. Designing a wall mount that would be adjustable according to a cartridge’s width isn’t terribly hard. Designing it well is somewhat challenging. Smaller cartridges, like the Game Boy, Game Gear and GB Advance carts would require a smaller solution, one they are also offering, but again with a different mounts for each cartridge. Their design is also lacking Famicom cart design.
Let’s take a look at the depth of the cartridge connectors’ grooves between a Famicom, NES, Mega Drive, Super NES and N64 game carts. To measure the depth, I am using metal ruler that starts from 0mm at its end and a caliper to measure the width of the connector groove.
Let’s put the NES images up before we compare the two.
The Famicom cart is shallower than its Western counterpart on either direction. The width is not a problem with either of these in the design they are currently using. The depth is a minor inconvenience, but 10mm is more than enough build a prong that holds NES cart in place. The plastic thickness is not a problem either, as long as the prongs are not made of too rigid material, which is a given. An adjustable arm could allocate both FC and NES carts just fine, as their design currently places the cartridge on two prongs that supports both front and back with one additional support column going into the groove. This additional piece is what keeps the cart straight, whereas the main prongs take the carts’ weight.
Their prototypes have been 3D printed and it shows. All the larger cartridges they have are slightly slanted forwards. This means they don’t only need to invest into material research than just create injection moulds.
The Mega Drive carts’ groove depth is a bit shallower than either FC or NES carts’, but the width is between NES’ and FC’s. Because the MD cart is shallower, the support column would need to be 1mm shorter, but at this scale and weight that’s not an issue with the right material.
Super NES/Famicom cartridges have the same width and depth across the board despite their different outer appearance between US and EUR/JPN region. The NES still has the widest groove, meaning SNES carts shouldn’t pose a problem with an adjustable arm.
The N64 has similar depth to the FC carts, but a Mega Drive cartridge still beats it. It’s width is the smallest, which means the adjustable hand should be at that size, minimum.
Let’s say that the adjustable arm is a design where there’s basically two tubes inside each other and you pull them out. If the minimum width is 70mm, it’s has enough room to spread at least 40mm either direction, adding a whopping extra 80mm to the total width, making the arm at 150mm at maximum, an unneeded amount. The needed width could be marked down with slots a peg slides into or with a small screw, both low in profile if done right. Another option is to position the adjuster the point where the mount is secured to the wall. Just have two slaps of plastic that you screw together at whatever distance from each you want. They wouldn’t even need to make large change in their current design to accommodate this.
If you have an access to a 3D printer, you could actually just use these measurements and do your own mounts if you wanted.
With Game Boy and GB Advance games, you have the exact same width and depth with both cartridges and there’s no good reason why to have separate mounts for both of them. Have the support wedged slightly into the connector groove and it would keep either GB or GBA carts in place.
A thing that I haven’t mentioned at all is thickness. For the record, here are the measurements for the carts used:
FC – 17mm
NES – 16.5mm
MD – 17mm
SFC/EUR SNES – 19.8mm in the middle, 17mm at screw point
US SNES – 20mm in the middle section, 17mm in outer sections
N64 – 18.9mm before tapering out
Having the main supports elongating to 18mm should be just fine, keeping the mount low profile. With the adjustable design, you could have the support prongs holding the cartridge in place with similar level of low profile.
The design given in the Kickstarter also leaves the cartridges’ connectors all open for further oxidation. While this is supposed to be a solution to problem of having games in boxes, which is really a non-problem to begin with, at least in these boxes the games were sealed from excess moisture and other unwanted materials floating in the air.
The problem of connectors being exposed is not really all that easy to solve without additional design tweaking. To keep the production as low as possible, you really can’t have luxuriously separate pieces that would seal the grooves, as they have a different height. The height with Nintendo’s cartridges’ are pretty solid 10-12mm, with N64 having the largest height, but also the thickest wall. Mega Drive’s height is same as N64’s; 12mm. The wall thickness is not the same across the board either. An adjustable solution for this would not be too low profile. A solution would be to have the lower support be thin enough but strong enough to be adjusted according the width and height, but as mentioned that’d skyrocket the costs both in design and production.
They also have basically opened some of the game boxes in their examples. These cardboard boxes are hard to come by as it is, and opening them as such ruins them. I hope they used a scan copy from the Internet.
I also have to question their advertisement slogan “Turn your games into unique wall art!” seeing there are thousands of these games out there.
Of course, you could also do what I did to throw some of my games to the wall and save some room while you’re at it. Just pick some shelves from Ikea and put your games on it. You can put more games on the wall that way, save some money and protect them from dust. Plus, when you’re tired with them you can use the shelves for whatever else than just stash the frames and mounts away.